AOPEN AK76F-1394 SIS IDE DRIVER DETAILS:
|File Size:||20.2 MB|
|Supported systems:||Windows 2K, Windows XP, Windows Vista, Windows Vista 64 bit, Windows 7, Windows 7 64 bit, Windows 8, Windows 8 64 bit, Windows 10|
|Price:||Free* (*Free Registration Required)|
AOPEN AK76F-1394 SIS IDE DRIVER
Overclocking refers to running a component at a speed greater than it was designed for.
This gives enhanced performance but often at the expense of decreased stability. Intel driver. Intel Network Drivers. This site maintains listings of network drivers available on the web, organized by company. Includes links to useful resources. PC maintenance article - It s AOpen AK76F-1394 SiS IDE brush based fan, which means it makes noise -particularly when it s cold at bootup.
Some also want to replace it to get better cooling. The most common way of doing this for most chipsets is to use a Blue Orb chipset cooler.
1GB 2X MB PC DDR DIMM pin Low Density Desktop Memory RAM Wundr-Shop
To start AOpen AK76F-1394 SiS IDE mod, I removed the old fan. You have to be careful when taking it off, because the back of the board has a lot of leads which can be scratched easily. Just use a needle nose pliers to clamp the plastic and push it through the hole. The fan will then remove with ease.
Lista sterowników Others w kategorii Płyty główne
Be careful not to scratch the leads on the back of the board I was surprised to find that Abit actually used thermal compound although a very small amount between the chipset fan and AOpen AK76F-1394 SiS IDE Northbridge. I didn t think there would be any kind of material there at all. Not much thermal compound Then I attached the Blue Orb. I soon found out that the Blue Orb does not fit on the KT7. Because of this, the Blue Orb is short by about half a centimeter. I tried bending it and forcing it on the board for about thirty minutes to no avail.
There is simply no possible way to get it to fit. Of course you can juse use thermal tape on the bottom without clamping the unit down, but this defeats the purpose of getting the added cooling of the Blorb. I then tried to mount the Blue Orb s fan on the KT7 s heatsink, since it was obvious the Blorb s fan was a tad better. This also was impossible to accomplish without some serious modification. The screws just don AOpen AK76F-1394 SiS IDE line up, and it s impossible AOpen AK76F-1394 SiS IDE force the screws into the heatsink believe me I tried.
Mounting the fan on the KT7 s heatsink won t work It is a good idea to take off the current heatsink and fan on the KT7 s Northbridge. Abit didn t use very much thermal paste at all.
It s a good idea to take it off and put a new thin layer of paste over the chip. It s possible this could further increase stability of the board, possibly allowing you to raise the FSB higher. Since AOpen AK76F-1394 SiS IDE have asked exactly how to remove the BIOS chip from the board, I have put together a short little guide. The BIOS chip is located on the bottom left of the board.
The writing on the chip not the sticker reads from the LEFT corner of the board - remember this when you put it back in. The chip is in it s socket rather securely.
Driver, SIS VGA Driver, R, 1/4/ Please have your SiS UniVGA3 driver updated to version R as well. SiS IDE Driver, Ra, 3/17/ Driver, SIS AOpen AK76F-1394 SiS IDE Driver, Ra, 6/4/, KB SiS IDE Driver, Ra, 3/17/, KB KB.
|Aeolus FX5900ULTRA-DVC256||Summary of Contents of user manual for Aopen ak76f400n|
|MSI Wind12 U210 Notebook Audio||Motherboard Others Drivers|
|Sony Vaio VPCF22BFXB Color Control Setting||Top drivers|
SIS VGA Driver for Win2K/XP/XP