EXTRON CTR 8 CONTROL MODULE DRIVER FOR WINDOWS 8

EXTRON CTR 8 CONTROL MODULE DRIVER DETAILS:

Type: Driver
File Name: extron_ctr_72713.zip
File Size: 40.0 MB
Rating:
4.48
8 (4.48)
Downloads: 8
Supported systems: Windows Vista (32/64-bit), Windows XP (32/64-bit), Windows 8, Windows 10
Price: Free* (*Free Registration Required)

Download Now
EXTRON CTR 8 CONTROL MODULE DRIVER



This symbol,when used on the product, is intended to alert the user of important operating and maintenance servicing instructions in the literature provided with the equipment. Dieses Symbol auf dem Produkt soll dem Benutzer in der im Lieferumfang enthaltenen Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung Instandhaltung geben.

The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference; the user must correct the interference at his own expense. Shielded cables must be used to ensure compliance with FCC emissions limits. Trademarks All trademarks mentioned in this Extron CTR 8 Control Module are the properties of their respective owners.

ATComputers 55I-750VPPage 9: Extron ctr 8, Transmit (tx) ground (g), Ctr 8 switcher, Extron in1606, Extron ipl 250
ADJ International S.r.l. MS-AC1111Ask a Question
ASRock 970 Extreme4 XFast RAM
Sony Vaio VPCSA4DFX
Agfa SnapScan e52

Attention indicates a situation that may damage or destroy the product or associated equipment. A note draws attention to important information. Software Commands Commands are written in the fonts shown here: From the File menu, select New. Click the OK button.

EXTRON CTR 8 CONTROL MODULE DRIVERS FOR WINDOWS VISTA

Specifications Availability Product specifications are available on the Extron website, www. It allows simple push-buttons to remotely switch and mute audio and video sources.

Extron Electronics CTR 8 Setup Manual

The CTR 8 accepts up to eight contact closure inputs and converts them to Extron CTR 8 Control Module serial commands that select the corresponding input on an Extron switcher. The following section covers rear panel features and cabling procedures. C GTurn Tx Goff and unplug their power cords. Power Supply Output Cord Figure 3.

Follow the same pin diagram above to connect a device to the Power Out connector. If it is any longer, the exposed wires may Extron CTR 8 Control Module, causing a short circuit between them. If it is any shorter, the wires can be easily pulled out even if tightly fastened by the captive screws. Use of an unauthorized power supply voids all regulatory compliance certification and may cause damage to the supply and the end product.

EXTRON ELECTRONICS CTR 8 SETUP MANUAL Pdf Download.

The power supply is to be located within the same vicinity as the Extron AV processing equipment in an ordinary location, Pollution Degree 2, secured to the equipment rack within the dedicated closet, podium or desk. The power supply shall not be permanently fixed to building structure or Extron CTR 8 Control Module structure. Wire each connector as shown in figure 4. Momentary closure of this pin to ground selects the corresponding number input. Selection is triggered specifically at the moment of closing, not opening.

When an input is Ground G selected, only the tally corresponding to that input is active. Determine and select the appropriate current-limiting resistor, if needed. Some button switches have the resistor built in. The host device is connected to the 3-pole captive screw connector on the rear panel. The protocol is baud, 8 data bit, 1 stop bit, and no parity. No special characters are required to begin or end a command sequence. When the CTR 8 determines that a command is valid, it executes the command Extron CTR 8 Control Module sends a response to the host device.

CTR 8-Initiated Messages When a local event such as a change in signal status takes place, the CTR 8 sends a message to the host, indicating the status change. No response is required from the host. When the CTR 8 is first switched on, it sends the message: Unless otherwise indicated, commands are not case-sensitive. This feature allows users to press the selected input button to mute and unmute the audio and video as needed during a presentation. SIS input selection for example, entering 1!

EXTRON CTR 8 CONTROL MODULE 64BIT DRIVER

Mutes video and sync Mute mode 0 is the normal default single state operation. See the next page Extron CTR 8 Control Module a partial list of Extron switchers that are compatible with the different mute modes. Other switchers and scalers are compatible with the mute modes. Contact Extron Technical Support for assistance with your Extron device. User Guide.

CTR 8. Switcher Accessories. Eight Input Contact Closure to RS Control Module. Rev. B. 03 The Extron CTR 8 adds contact closure control to most RS controllable Extron single-output simple or scaling switchers, or to an Extron IP Link control.

Other Drivers